Home > Hard Drive > EIDE Hard Drive Install Problem.

EIDE Hard Drive Install Problem.

Contents

All clean of course. as far as I know. If you are replacing a drive, get a recovery disc set for your exact model of computer. Well it sounded so simple but no matter what I do I cannot get the computer to recognize my old drive connected to the slave connecter on the cable. this contact form

just look at the power connectors in your computer, then double check what connector your drive requires and go buy it. When your tractor breaks or your cell phone stops working, they want to be the only people who can fix it. It requires manufacturers to provide owners and independent repair shops with access to repair information and replacement parts—so you have the resources you need to fix things quickly and affordably. When your tractor breaks or your cell phone stops working, they want to be the only people who can fix it. http://support.wdc.com/knowledgebase/answer.aspx?ID=981

Western Digital Ide Hard Drive Jumper Settings

Thanks for the instructions! This will prevent frustrations about losing programs after you have already formatted your computer.If you are simply installing a secondary hard drive for storage, you don't have to make any changes Protect the drive from static discharge by wearing a grounded wrist strap. and ur write he DIDNT start off with TAKE drive out of box… jeeees….

Reply James Scholes on June 23, 2009 at 2:47 pm Hi, I have a drive mounted in an external enclosure, on which the power supply has gone dead. Open 'er up and check out all your connections. For that you will have to pull off both side panels to your case. Why Is It Necessary To Partition The Hard Disk While Installing Operating System? This may still occur even if you are installing a single drive.

Extra big thanks to suRoot for saying to set the jumpers on the IDE (secondary) drive on the computer to cable-select before plugging it in! Seagate Ide Hard Drive Jumper Settings If a properly installed SATA drive is not recognized by the operating system, verify that BIOS Setup is configured properly and that you have loaded and enabled the latest driver for My hard drive doesn't have the jumper settings on the label: Find the model number and visit the manufacturers website. http://www.computerhope.com/issues/ch000413.htm Don't force it.

Follow the instructions in Answer ID 3865: How to partition and format a WD drive on Windows and macOS for Windows Vista. How To Connect Ide Hard Drive To Sata Motherboard Figure : Finding the version for BIOS version 7 or greater If your computer has BIOS version 7 or greater, go to Configuring the hard drive in BIOS version 7 or Your cache administrator is webmaster. You have to click the Action button.

Seagate Ide Hard Drive Jumper Settings

small four prong or SATA connection on the drive. https://www.pcmech.com/article/installing-a-hard-drive-step-by-step/ If a second hard drive was added, use the following steps: Click Start , then click Computer. Western Digital Ide Hard Drive Jumper Settings Once you’ve got it in, don’t forget to format the drive How To Format A Large Hard Drive With Either FAT Or FAT32 How To Format A Large Hard Drive With Jumper Setting For Sata Hard Disk IDE Cables Let’s look at some standard IDE cables and connectors.

Step-by-step instructions follow below. weblink other then that its not able to without this the drive will not read and be able to transfer files Reply Gary Hart on August 7, 2007 at 4:46 am Thanks Once connected, turn on the computer and as the computer is booting, enter BIOS setup. Attach Cables Once the jumpers have been verified and the hard is attached and secured to the computer case, connect the cables to the computer hard drive. How To Connect Ide Hard Drive To Motherboard

  1. Reply Dinis on May 11, 2009 at 2:24 am David,Thank You for the above web site that help me install the hard disk and and on formatting the second half of
  2. I was trying to set the 2 HDD on IDE1 (Secondary) as Master and slave, and it wouldn't work.
  3. Follow the on-screen instructions.
  4. If it does not you will need to contact your system or motherboard manufactuer for assistance.
  5. Drive cage examples Step 4: Removing the drive If the drive is attached to the chassis or drive cage with screws, remove the screws and slide the drive out.
  6. Many older power supplies do not provide SATA power connectors.
  7. Although it is not a major issue, we prefer to use a dedicated power cable for a hard drive whenever possible, rather than sharing a power cable among two or more
  8. When I try to boot up the new HD using my Windows boot/installation disk, I get a message that Setup could not find any HD installed on my PC.

Reply Nick on August 22, 2009 at 4:15 am awesome. Open up your computer case. I dont know what you guys are doing wrong.. http://filevox.com/hard-drive/erasing-hard-drive-problem.html I've saved this to my useful websites list for easy reference!Thanks, matey!

Make sure that all of the connectors are fully seated. Jumper Setting On Hard Disk It does not recognise the difference in size. Reply Mark on January 31, 2008 at 2:43 am My old hard drive crashed.

Wanted to install in new box.

You may assign a drive letter that is not in use by other devices if you wish, then left-click on Next to continue. note: Your case will probably be different than the case example used in the video. Step 1: Opening the case Use the following steps to open the case: warning: The If the new drive displays with usable space, you are done. How To Install Ide Hard Drive I do not have the option in the BIOS to boot from SCSI device, as mentioned.

Tell them you support a bipartisan bill. Click Next to continue. Look in the folder "my computer" Do you see it there? his comment is here At startup, run the CMOS Setup program and configure your BIOS so your drive is detected.

To connect the IDE cable to the motherboard you'll have to find something that looks like this: Each connector represents 1 IDE channel. They are not nerds, merely computer literate. Good job A+ on te article Reply RepairGal on January 8, 2009 at 9:42 pm Anyone who doesn't understand what a "jumper" is shouldn't be trying to change out their hard This pin always goes on the same side as the power connector.